Como modificar la luz del encendedor del Chery Orinoco A3

How to modify the light of the lighter of the Chery Orinoco A3

New product

In this article, Chica Mecánica shows you how to modify the lights of the lighter of the Chery Orinoco A3 and give it a much more attractive, easy and simple effect as always.

How to modify the lights of the lighter of the Chery Orinoco A3

Hello that, as always today I bring you a very simple way of tuning the lighter of a Chery Orinoco or A3 in a very simple way that you can easily do at home.

Usually in the economic models of this car has all the wiring for the lighting of the lights of the buttons of the board, suiches of electric windows, lighter among others, only that they do not place the lights. Then with a bit of expertise and my help they can make a very good personalization that will not take more than a couple of hours.
For my case I wanted to do in addition to lighting the lighter, achieve a heat effect inside the lighter. This I will illuminate with red color the chromed interior where the lighter goes.

Materials:

- Two LEDs (Color you want)
- A resistance of 680ohms 1 / 4W
- A resistance of 10k ohms 1 / 4W
- Rigid cables, tin and a soldering iron.


Steps to remove the console:

1.- Remove 3 screws that hold the igniter console and shift lever.

- Two forward under the black carpet
- One below the ash deposit

2.- Pull the back part firmly upwards until it loosens.

3.- Then take out the ring that holds the lever cover up.

4.- Finally disconnect the cigarette lighter connector and remove the console.

Below I leave the video of how I did it, there is step by step how to make this modification

Description of lighter terminals

In the following figure you can see the meaning of each lighter terminal seen from above.

Descripcion terminales encendedor del chery orinoco a3
There are the two main terminals with positive and negative to energize the lighter plus two more that are positive that comes from the switchboard of lighting control of the board.
Important! The load for this light terminal must always be LEDs, do not place incandescent lights or it could damage the control unit.

Proposed circuit for our modification

It is quite simple and the following figure speaks for itself.

circuito encendedor chery a3
 
The LED that has the resistance of 10 k ohms should illuminate the acrylic, this is very important because with this resistance we ensure that we work with the intensity control of the light switchboard. If we put another value; or it will light too much, or it will light very little besides that it will not diminish the intensity as in the other lights.
The LED that has the resistance of 680 ohms we place it to shine into the lighter, to give the effect of heat on.

Considerations in this design

Protect the cables of the circuit so there are no short circuits.
Do not confuse the resistances to achieve the desired effect.
Arrange the cables and LEDs so that they do not touch the metal part of the lighter, as it will heat up and damage them.
Well, it's all for today. I have nothing left to do but wait.

Well, it's all for today and I hope you like this proposal. Remember that if you have any suggestions or questions, below is the box for it. As you can see it is quite simple to do and really the work is worth it and more if the cost is almost nothing.

Here below I leave the video of how I did it



Ahhhh can give your impressions of this article by writing your opinion up on the opinions button.

Questions or suggestions?

Down in the question box.

Follow me on Social Networks

boton de chica mecanica youtobeboton chica mecanica instagram

Written by
Dennis Garcia
06/25/2017

Grade 
06/25/2017

Me gusto

Otro aporte más a la comunidad.

    Write your review!

    Write a review

    How to modify the light of the lighter of the Chery Orinoco A3

    How to modify the light of the lighter of the Chery Orinoco A3

    In this article, Chica Mecánica shows you how to modify the lights of the lighter of the Chery Orinoco A3 and give it a much more attractive, easy and simple effect as always.

    Ask a question

    NO registration required!

    2 Question(s) answered

    If the question you have has not yet been answered here, use the form below to ask something about this addon.

    (optional)
    *(Required to be notified when an answer is available)
    Send question!
    • Asked by fidel borjas s
      on 04/16/2018       hola disculp queria saber si me puedes ayudar con un problema. que tengo. es un carroOrinoco si lo mantengo hasta 100 kil.por hora no pasa nada pero si se me ocurre pasarlo d 100kl. se recalienta y feo no se que hacer. Answer:
      Fidel, tienes problemas de siciedad graves en el radiador.
    • Asked by reinaldo
      on 07/07/2018       hola deseo saber en que parte va el modulo de retroceso del chery orinoco espero su pronta repuesta Answer:
      Ese modulo no lo he buscado Reinaldo.

    If the download link redirects to another product that is not described in the article or is broken, report it using our Reporting Form

    RelatedProducts

    In this article I explain how it works and how to identify a CKP sensor (crankshaft sensor) for induction and Hall effect.
    In this article I show you how to build a CKP or CMP automobile sensor tester. Simple and very practical.
    In this article I show you some tips on how to change the spark plug wires of the Chery Orinoco A3.
    Learn with Mechanic Girl to build a rudimentary 12V battery charger, effective and as always simple to do.
    In this blog article, Chica Chica shows us how to make an effective battery charge tester that we can do in our case or workshop.
    Acceleration failure of the Chery Orinoco or A3, because the fault is often of this sensor. Learn to try it with Mechanical Girl.
    In this article Mechanical Girl solves a problem of lack of spark in a cylinder of the Chery Arauca or A1.
    In this article I explain what is and how the engine coolant works. Also I show you tips of which refrigerant to use.
    Hello, in this opportunity I show you how to test a coil without drying without integrated power circuit. And I do it thanks to a rudimentary little tester.
    In this article I talk a little about what spark plugs are, how they work inside the engine, types and some problems associated with them.
    In this article Chica Mecánica explains what to do before changing the spark plugs of our car and how to know if they are damaged.
    In this article, Chica Mecánica shows us where the Chery Orinoco or A3 sensors are.
    In this article, Chica Mecánica makes a simple circuit that can measure the charge of a car battery. Very simple to do and economical.
    In this article, mechanical girl shows us some procedures how to know if the CKP is responsible for the engine does not turn on. As always, simple to realize and easy to understand.
    In this article, mechanical girl shows us how to test the cooling system of an engine and its possible failures. In this case for a Toyota Starlet.
    Here I show you all the home automotive sensor testers that I have done and shared by my YouTube channel and my blog. Easy to make.
    Solve the faults in a simple way with this continuity tester with sound and light that you can do in a homemade way and with simple materials.
    En este video te enseño a construir un probador de sensor ABS de efecto HALL, que por lo general usa dos cables. Este circuito lo puedes hacer en tu casa o taller de forma sencilla.
    En este video realizo la prueba del sensor/suiche del retroceso del Chery Orinoco o A3. Por lo general esta es la falla más común cuando hay problemas con el encendido de las luces de retroceso y el sonar del carro.
    Here I am talking about the IAC of 3 cables. How to perform tests, with tester, multimeter measurement and electrical diagram that will let them know if it works or not.
    En este artículo chica mecánica explica que es la válvula PCV, su funcionamiento, como realizar pruebas y cuales son las fallas para corrregirlas.
    In this article it is explained, that it is an injector, how the computer handles the injection pulse and how an injector pulse tester is made.
    Aquí describo como hacer las pruebas para saber si hay pulsos de inyeccion de la computadora. Asi descartar problemas de CKP, cableado o inmovilizador.
    In this article I explain how an injector works electrically. With diagrams, circuits and images, very easy to understand.
    Pulse generator for gas injectors that you can do at home. Simple to assemble and without many components. Made by Mechanical Girl.
    What is it? function of the hydraulic oil pressure sensor. Explained by Mechanical Girl.
    In this article Chica Mecanica explains how to disassemble the radiator of the Chery Orinoco or A3. In simple steps, with photos and video.
    In this article you will learn to know the most important components of the Air Conditioning System
    Here I am talking about the IAC of 3 cables, toyota model. How to perform tests, with tester, multimeter measurement and electrical diagram that will let them know if it works or not.
    In this article you will learn to know the most important components of the Air Conditioning System